Re: [Linux-31] Probleme avec disk dur : Error mounting /dev/sdc1...

[Christophe VANHOUTTE <tx1138 AT gmail.com>]

Bonjour,

Aie , cela ''ne sent pas bon'' , pourtant ce disk à tourné que 347 heures selon les logs

voici le :

smartctl -a /dev/sdb

smartctl 6.6 2017-11-05 r4594 [x86_64-linux-4.19.0-14-amd64] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Western Digital Blue
Device Model:     WDC WD40EZRZ-00WN9B0
Serial Number:    WD-WCC4E7CA97YE
LU WWN Device Id: 5 0014ee 2b799be22
Firmware Version: 80.00A80
User Capacity:    4 000 787 030 016 bytes [4,00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5400 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-2 (minor revision not indicated)
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is:    Sat Mar  6 22:41:41 2021 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART Status command failed: Connexion terminée par expiration du délai d'attente
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.

General SMART Values:
Offline data collection status:  (0x82)    Offline data collection activity
                    was completed without error.
                    Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)    The previous self-test routine completed
                    without error or no self-test has ever
                    been run.
Total time to complete Offline
data collection:         (54240) seconds.
Offline data collection
capabilities:              (0x7b) SMART execute Offline immediate.
                    Auto Offline data collection on/off support.
                    Suspend Offline collection upon new
                    command.
                    Offline surface scan supported.
                    Self-test supported.
                    Conveyance Self-test supported.
                    Selective Self-test supported.
SMART capabilities:            (0x0003)    Saves SMART data before entering
                    power-saving mode.
                    Supports SMART auto save timer.
Error logging capability:        (0x01)    Error logging supported.
                    General Purpose Logging supported.
Short self-test routine
recommended polling time:      (   2) minutes.
Extended self-test routine
recommended polling time:      ( 542) minutes.
Conveyance self-test routine
recommended polling time:      (   5) minutes.
SCT capabilities:            (0x7035)    SCT Status supported.
                    SCT Feature Control supported.
                    SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   200   200   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0027   175   170   021    Pre-fail  Always       -       8233
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       227
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   200   200   000    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       -       347
 10 Spin_Retry_Count        0x0032   100   100   000    Old_age   Always       -       0
 11 Calibration_Retry_Count 0x0032   100   100   000    Old_age   Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       226
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       105
193 Load_Cycle_Count        0x0032   199   199   000    Old_age   Always       -       3937
194 Temperature_Celsius     0x0022   119   104   000    Old_age   Always       -       33
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   200   200   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   200   200   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0008   200   200   000    Old_age   Offline      -       0

SMART Error Log Version: 1
ATA Error Count: 2
    CR = Command Register [HEX]
    FR = Features Register [HEX]
    SC = Sector Count Register [HEX]
    SN = Sector Number Register [HEX]
    CL = Cylinder Low Register [HEX]
    CH = Cylinder High Register [HEX]
    DH = Device/Head Register [HEX]
    DC = Device Command Register [HEX]
    ER = Error register [HEX]
    ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 2 occurred at disk power-on lifetime: 345 hours (14 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  04 61 00 53 4f c2 a0  Device Fault; Error: ABRT

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  b0 d8 00 01 4f c2 a0 00      00:00:59.606  SMART ENABLE OPERATIONS
  ec 20 3f 01 00 00 a0 00      00:00:59.605  IDENTIFY DEVICE
  10 20 3f 01 00 00 a0 00      00:00:59.604  RECALIBRATE [OBS-4]
  91 20 3f 01 00 00 af 00      00:00:59.591  INITIALIZE DEVICE PARAMETERS [OBS-6]
  ec 00 00 01 00 00 a0 00      00:00:28.838  IDENTIFY DEVICE

Error 1 occurred at disk power-on lifetime: 345 hours (14 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  04 61 00 53 4f c2 a0  Device Fault; Error: ABRT

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  b0 d8 00 01 4f c2 a0 00      00:00:04.170  SMART ENABLE OPERATIONS
  ec 20 3f 01 00 00 a0 00      00:00:04.170  IDENTIFY DEVICE
  10 20 3f 01 00 00 a0 00      00:00:04.164  RECALIBRATE [OBS-4]
  91 20 3f 01 00 00 af 00      00:00:04.164  INITIALIZE DEVICE PARAMETERS [OBS-6]
  ec 00 00 01 00 00 a0 00      00:00:04.162  IDENTIFY DEVICE

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

Christophe

Le 07/03/2021 à 08:24, jdanield (via linux-31 Mailing List) a écrit :

    Le
      06/03/2021 à 22:49, Christophe VANHOUTTE (via linux-31 Mailing
      List) a écrit :
      
      
> Error mounting /dev/sdc1 at
>         /media/yoda/sata3: can't read superblock on /dev/sdc1.
>         
>       
      
      ça sent pas bon
      
      
> _La partition 4 ne commence pas sur une
>         frontière de cylindre physique._
>         
>       
      
      ça n'est pas grave
      
      
> sata3: recovering journal
>         
>         JBD2: Invalid checksum recovering block 288 in log
>         
>       
      (...)
      
      
      ça sent pas bon
      
      
> J'ai un resultat smartctl en stock si
>         besoin.
>         
>       
      
      c'est le premier que tu aurais du donner...
      
      
      jdd
      
      
      
      
--

Debian Duster 10.8|Kernel 4.19.0-14-amd64|Xorg 1.20.4 & Xfce 4.12
http://www.debian.org # http://fr.wikipedia.org/wiki/Obsolescence
https://soutien.laquadrature.net/
http://gnutux.free.fr # Il faut dire GNU/Linux :) # www.culte.org
-- 
GNU/Linux : May the Force be with you !